<![CDATA[Add Custom:Device to channels monitored for a button]]>I've noticed that (at least on Asterisk 10, and presumably on any version post 1.6 that supports DEVICE_STATE) the AMI is sending events for when a Custom device changes state; is there any way FOP can be extended to use these events? I deleted my debug file earlier, but I can get the events again for you this evening/weekend if you want.

]]>http://localhost:4567/topic/1061/add-custom-device-to-channels-monitored-for-a-buttonRSS for NodeTue, 27 Oct 2026 08:08:05 GMTFri, 24 Feb 2012 21:21:02 GMT60<![CDATA[Reply to Add Custom:Device to channels monitored for a button on Tue, 20 Mar 2012 00:13:07 GMT]]>If you have both channels active on inbound calls, it will show the two lines ringing as both channel are ringing. If only one rings, you will see only one line.

]]>http://localhost:4567/post/4734http://localhost:4567/post/4734Tue, 20 Mar 2012 00:13:07 GMT<![CDATA[Reply to Add Custom:Device to channels monitored for a button on Mon, 19 Mar 2012 05:54:58 GMT]]>Hi Nicolas,

Great thanks for your prompt answer.
I set the following button:

[SIP/9791]
type=extension
extension=9700
context=local
label=Virtual Test
channel=SIP/9778

It works as expected for outgoing call, but for incoming calls it shows 2 lines, could I prevent this behavior to show only one line?

Best regards,
Christian

]]>http://localhost:4567/post/4733http://localhost:4567/post/4733Mon, 19 Mar 2012 05:54:58 GMT<![CDATA[Reply to Add Custom:Device to channels monitored for a button on Sun, 18 Mar 2012 20:16:37 GMT]]>fop2 can monitor multiple devices for one button using the channel directive, so if you have a button for one sip device, you can extend it to monitor other devices by adding the propper channel directives:

[SIP/100]
type=extension
extension=100
context=from-internal
label=John
channel=SIP/200

with the above setting , calls for both SIP/100 and SIP/200 will be shown on that button status. If you use fop2admin, you have a channel field to set in every button, you can add several channel separated with &.

A not of warning, when a button monitors more than one channel, you cannot have ANOTHER button displaying status for those extra channels.

Best regards,

]]>http://localhost:4567/post/4732http://localhost:4567/post/4732Sun, 18 Mar 2012 20:16:37 GMT<![CDATA[Reply to Add Custom:Device to channels monitored for a button on Sun, 18 Mar 2012 12:20:38 GMT]]>I would like to react on this request because I have an example

I have a configuration for some users: 1 deskphone, 1 dect phone and 1 dialplan extension for both.
exten => 300,1,Dial(SIP/400&SIP/500)
exten => 300,hint,SIP/400&SIP/500

I am using DEVICE_STATE to check the status, and when 400 or 500 is making a call.
I am showing 300 on the callee display

Will it be possible for Flash Operator Panel to show 300 as an extension button and to report line status as a physical extension?

Thanks in advance

]]>http://localhost:4567/post/4731http://localhost:4567/post/4731Sun, 18 Mar 2012 12:20:38 GMT<![CDATA[Reply to Add Custom:Device to channels monitored for a button on Sat, 25 Feb 2012 02:54:38 GMT]]>What do you want to monitor exactly? What is your idea? Can you give an example? Manager events will also be helpful.

Best regards,

]]>http://localhost:4567/post/4730http://localhost:4567/post/4730Sat, 25 Feb 2012 02:54:38 GMT