All I had to do was reboot! :lol:

then look inside XXXXXX.cfg, the buttons are there. If you have a file with just an

#exec autoconfig-buttons-freepbx.sh

so I have left it alone, and I ran ./autoconfig-buttons-freepbx.sh only to find that it didn't output anything, said it did, to what file I don't know, that was my original question.
What file is fop2 reading from to get the buttons, after you have run the script outputs to where? I have exceeded over 15 so i need to delete some of them that are in call groups anyways... but I have no idea what file to delete these from.

I really don't know what is wrong. Would hater to start over again when this is all that I have left.

Thanks,

./autoconfig-users-freepbx.sh

Look at the output, at the end you will see a line like:

buttonfile=XXXXXX.cfg

then look inside XXXXXX.cfg, the buttons are there. If you have a file with just an

#exec autoconfig-buttons-freepbx.sh

Then leave that file alone and run in the command line:

./autoconfig-buttons-freepbx.sh

That script will output the button config, if its wrong, you can fix the script to your liking, like adding the full path to the asterisk binary, changing ZAP to DAHDI, etc... The idea is that the script will output the proper FOP2 button configuration for your PBX.

Best regards,

my fop2.cfg file looks like this:

[general]
; AMI definitions
manager_host=127.0.0.1 ;200.61.177.141
manager_port=5038
manager_user= user
manager_secret=password
;event_mask=call,agent

; Daemon definitios
listen_port = 4444
;restrict_host = www.asternic.org
web_dir = /var/www/html/fop2

; Global Config
language = en
poll_interval = 86400
poll_voicemail = 1

;master_key = 5678

; USER LIST
;user=620all
;user=621all
;user=622all
;user=623:1234all

buttonfile=buttons.cfg

blind_transfer=1

#exec autoconfig-users-freepbx.sh

With this pointing to the buttons.cfg for the users shouldn't this work? Where is Fop getting its button info from???
Its not reading this file.

Please help... I believe that I am getting close.
What am I doing wrong now... :lol: These trunks are the last thing to configure within my AsteriskNOW setup..

Thanks in advance.

sh autoconfig-buttons-freepbx.sh > buttons.cfg
autoconfig-buttons-freepbx.sh: line 45: asterisk: command not found

$nano autoconfig-buttons-freepbx.sh
Referring to First line here :

DAHDI=asterisk -rx "zap show channels" | grep -v from-internal | grep -v pseudo | grep -v Language | awk '{print $1}' | head -n 1
if [ "X${DAHDI}" != "X" ]; then
echo
echo "[DAHDI/$DAHDI]"
echo "type=trunk"
echo "label=DAHDI"
asterisk -rx "zap show channels" | grep -v from-internal | grep -v pseudo | grep -v Language | awk '{print $1}' | tail -n 2 | while read LINEA
do
echo "channel=DAHDI/$LINEA"
done
fi

Fix:
change first line where says 'asterisk -rx' to /usr/sbin/asterisk -rx
and also changing the "zap show channels" to "dahdi show channels"
seems to create the file correctly

Best regards,

Trunk buttons are actually "GROUP" buttons, in the sense that no matter how many channels you list, you will only see ONE button.

[DAHDI/1]
type=trunk
channel=DAHDI/2
channel=DAHDI/3

.. will show 1 button, not 3.

Not sure if you have that problem, but it is a good place to clear this question out.

Finally, if you use auto configuration using #exec, you cannot use at the same time static configs.. I will try to fix that on the next release, although is kind of difficult and I do not want to delay the release much longer.

Best regards,

Thanks in advance