127.0.0.1 failed to authenticate as 'fop2'
Running Freepbx 13 with Asterisk 11.25 on Centos 6.6.
I have been getting this error message for a bit on the Asterisk CLI
NOTICE[5033]: manager.c:2677 authenticate: 127.0.0.1 failed to authenticate as 'fop2'
I dont know whether a Freepbx update broke the config setup, or whether I changed something and broke it !
I have tried changing the manager_user and manager_secret back to the FOP settings but that doesnt seem to make a difference.
Can you point me where else I should be looking
Thanks in advance
Here's a snippet from /usr/local/fop2/fop2.cfg
[general]
; AMI definitions
manager_host=localhost
manager_port=5038
;manager_user=fop2
manager_user=admin
manager_secret=myownsecret
;manager_secret=fop222
;event_mask=agent,call,command,system,user,dialplan
/etc/asterisk/manager.conf
;
; AMI - Asterisk Manager interface
;
; FreePBX needs this to be enabled. Note that if you enable it on a different IP, you need
; to assure that this can't be reached from un-authorized hosts with the ACL settings (permit/deny).
; Also, remember to configure non-default port or IP-addresses in amportal.conf.
;
; The AMI connection is used both by the portal and the operator's panel in FreePBX.
;
; FreePBX assumes an AMI connection to localhost:5038 by default.
;
[general]
enabled = yes
port = 5038
bindaddr = 127.0.0.1
displayconnects=no ;only effects 1.6+
[admin]
secret = myownsecret
deny = 0.0.0.0/0.0.0.0
permit = 127.0.0.1/255.255.255.0
read = all
write = all
writetimeout = 5000
eventfilter=!Event: RTCP*
eventfilter=!Event: VarSet
eventfilter=!Event: Cdr
eventfilter=!Event: DTMF
eventfilter=!Event: AGIExec
eventfilter=!Event: ExtensionStatus
eventfilter=!Event: ChannelUpdate
eventfilter=!Event: ChallengeSent
eventfilter=!Event: SuccessfulAuth
[admin]
secret = myownsecret
deny = 0.0.0.0/0.0.0.0
permit = 127.0.0.1.255.255.255.0
read = all
write = all
[admin]
secret = myownsecret
deny=0.0.0.0/0.0.0.0
permit=127.0.0.1/255.255.255.0
read = system,call,log,verbose,command,agent,user,config,command,dtmf,reporting,cdr,dialplan,originate,message
write = system,call,log,verbose,command,agent,user,config,command,dtmf,reporting,cdr,dialplan,originate,message
writetimeout = 5000
[admin]
secret = myownsecret
deny = 0.0.0.0/0.0.0.0
permit = 127.0.0.1/255.255.255.0
read = all
write = all
writetimeout = 5000
eventfilter=!Event: RTCP*
eventfilter=!Event: VarSet
eventfilter=!Event: Cdr
eventfilter=!Event: ExtensionStatus
eventfilter=!Event: ChannelUpdate
#include manager_additional.conf
#include manager_custom.conf
[admin]
secret = myownsecret
deny=0.0.0.0/0.0.0.0
permit=127.0.0.1/255.255.255.0
displayconnects = no
read = system,call,log,verbose,command,agent,user,originate
write = system,call,log,verbose,command,agent,user,originate
I have been getting this error message for a bit on the Asterisk CLI
NOTICE[5033]: manager.c:2677 authenticate: 127.0.0.1 failed to authenticate as 'fop2'
I dont know whether a Freepbx update broke the config setup, or whether I changed something and broke it !
I have tried changing the manager_user and manager_secret back to the FOP settings but that doesnt seem to make a difference.
Can you point me where else I should be looking
Thanks in advance
Here's a snippet from /usr/local/fop2/fop2.cfg
[general]
; AMI definitions
manager_host=localhost
manager_port=5038
;manager_user=fop2
manager_user=admin
manager_secret=myownsecret
;manager_secret=fop222
;event_mask=agent,call,command,system,user,dialplan
/etc/asterisk/manager.conf
;
; AMI - Asterisk Manager interface
;
; FreePBX needs this to be enabled. Note that if you enable it on a different IP, you need
; to assure that this can't be reached from un-authorized hosts with the ACL settings (permit/deny).
; Also, remember to configure non-default port or IP-addresses in amportal.conf.
;
; The AMI connection is used both by the portal and the operator's panel in FreePBX.
;
; FreePBX assumes an AMI connection to localhost:5038 by default.
;
[general]
enabled = yes
port = 5038
bindaddr = 127.0.0.1
displayconnects=no ;only effects 1.6+
[admin]
secret = myownsecret
deny = 0.0.0.0/0.0.0.0
permit = 127.0.0.1/255.255.255.0
read = all
write = all
writetimeout = 5000
eventfilter=!Event: RTCP*
eventfilter=!Event: VarSet
eventfilter=!Event: Cdr
eventfilter=!Event: DTMF
eventfilter=!Event: AGIExec
eventfilter=!Event: ExtensionStatus
eventfilter=!Event: ChannelUpdate
eventfilter=!Event: ChallengeSent
eventfilter=!Event: SuccessfulAuth
[admin]
secret = myownsecret
deny = 0.0.0.0/0.0.0.0
permit = 127.0.0.1.255.255.255.0
read = all
write = all
[admin]
secret = myownsecret
deny=0.0.0.0/0.0.0.0
permit=127.0.0.1/255.255.255.0
read = system,call,log,verbose,command,agent,user,config,command,dtmf,reporting,cdr,dialplan,originate,message
write = system,call,log,verbose,command,agent,user,config,command,dtmf,reporting,cdr,dialplan,originate,message
writetimeout = 5000
[admin]
secret = myownsecret
deny = 0.0.0.0/0.0.0.0
permit = 127.0.0.1/255.255.255.0
read = all
write = all
writetimeout = 5000
eventfilter=!Event: RTCP*
eventfilter=!Event: VarSet
eventfilter=!Event: Cdr
eventfilter=!Event: ExtensionStatus
eventfilter=!Event: ChannelUpdate
#include manager_additional.conf
#include manager_custom.conf
[admin]
secret = myownsecret
deny=0.0.0.0/0.0.0.0
permit=127.0.0.1/255.255.255.0
displayconnects = no
read = system,call,log,verbose,command,agent,user,originate
write = system,call,log,verbose,command,agent,user,originate