Need help with initial config on clean Asterisk.

[suncheez]

Hello.

Trying to set up the FOP2 at the clean asterisk 1.4 installation.
I've manually copied files and folders and trying to start the FOP2, but have no luck.

/usr/local/fop2/fop2_server --test

Flash Operator Panel 2 - No valid license found. Demo Mode
Couldn't connect to localhost:5038 (Server 0)

then I've checked iptables.

/etc/init.d/iptables status

Table: filter
Chain INPUT (policy ACCEPT)
num target prot opt source destination
1 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0

Chain FORWARD (policy ACCEPT)
num target prot opt source destination
1 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0

Chain OUTPUT (policy ACCEPT)
num target prot opt source destination

Chain RH-Firewall-1-INPUT (2 references)
num target prot opt source destination
1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0
2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 255
3 ACCEPT esp -- 0.0.0.0/0 0.0.0.0/0
4 ACCEPT ah -- 0.0.0.0/0 0.0.0.0/0
5 ACCEPT udp -- 0.0.0.0/0 224.0.0.251 udp dpt:5353
6 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:631
7 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:631
8 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED
9 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22
10 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80
11 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:5060
12 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:5060
13 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:4445
14 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:5038
15 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:5038
16 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited

Here the fop2.cfg:

[general]
; AMI definitions
manager_host=localhost
manager_port=5038
manager_user=asdasd
manager_secret=wertyuiop
event_mask=agent,call,command,system,user,dialplan

; Daemon definitios
listen_port = 4445
;restrict_host = http://www.asternic.org
web_dir = /var/www/html/fop2

Any suggestions where I lamed up?

[nicolas]

Check /etc/asterisk/manager.conf and be sure that you have the manager service enabled. You can check if the service is up by using the command:

netstat -lnp | grep 5038

Best regards,

[suncheez]

Oh, forgive the newbie!
Ofcourse it was "enabled = no".
Thnx a lot.