Hi all.
I've recently installed FOP2 version 2.26 for a 64bit CentOS (fop2-2.26-centos5-x86_64.tgz)
This server has a FreePBX installation, but I cannot login. The login screen appears very well, but when I introduce any extension, regardless if the password is right or wrong I always get the "One moment please" and after 16 connection to the server retries I get the "System is not available right now". I followed all the steps from the setup guide.
If I run "./fop2_server --debug 9" I can see al the messages between FOP2 and Asterisk via AMI. I can see the retrieval of all extensions states, even the SIP trunks:
Flash Operator Panel 2 - No valid license found. Demo Mode
** MANAGER CONNECTION Connecting to localhost:5038 (Server 0)
** MANAGER CONNECTION Connected to localhost:5038 (Server 0)
127.0.0.1 <- Asterisk Call Manager/1.1
127.0.0.1 <- Response: Success
127.0.0.1 <- Challenge: 469955471
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- Message: Authentication accepted
127.0.0.1 <- Server: 0
127.0.0.1 <- Event: FullyBooted
127.0.0.1 <- Privilege: system,all
127.0.0.1 <- Status: Fully Booted
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- ActionID: getvar!coresettings
127.0.0.1 <- AMIversion: 1.1
127.0.0.1 <- AsteriskVersion: 1.8.15.0
127.0.0.1 <- SystemName:
127.0.0.1 <- CoreMaxCalls: 0
127.0.0.1 <- CoreMaxLoadAvg: 0.000000
127.0.0.1 <- CoreRunUser:
127.0.0.1 <- CoreRunGroup:
127.0.0.1 <- CoreMaxFilehandles: 0
127.0.0.1 <- CoreRealTimeEnabled: Yes
127.0.0.1 <- CoreCDRenabled: Yes
127.0.0.1 <- CoreHTTPenabled: No
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- Message: Mailbox Status
127.0.0.1 <- Mailbox: 26109@default
127.0.0.1 <- Waiting: 0
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- Message: Mailbox Message Count
127.0.0.1 <- Mailbox: 26109@default
127.0.0.1 <- UrgMessages: 0
127.0.0.1 <- NewMessages: 0
127.0.0.1 <- OldMessages: 0
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- Message: Channel status will follow
127.0.0.1 <- Server: 0
127.0.0.1 <- Event: PeerEntry
127.0.0.1 <- Channeltype: SIP
127.0.0.1 <- ObjectName: mitel-in
127.0.0.1 <- ChanObjectType: peer
127.0.0.1 <- IPaddress: 10.217.115.2
127.0.0.1 <- IPport: 5060
127.0.0.1 <- Dynamic: no
127.0.0.1 <- Forcerport: yes
127.0.0.1 <- VideoSupport: yes
127.0.0.1 <- TextSupport: no
127.0.0.1 <- ACL: no
127.0.0.1 <- Status: OK (13 ms)
127.0.0.1 <- RealtimeDevice: no
127.0.0.1 <- Server: 0
127.0.0.1 <- Event: PeerlistComplete
127.0.0.1 <- EventList: Complete
127.0.0.1 <- ListItems: 1336
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- EventList: start
127.0.0.1 <- Message: Peer status list will follow
127.0.0.1 <- Server: 0
Response: Success
EventList: start
Message: Peer status list will follow
Server: 0
127.0.0.1 <- Event: PeerlistComplete
127.0.0.1 <- EventList: Complete
127.0.0.1 <- ListItems: 0
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Success
127.0.0.1 <- Message: Parked calls will follow
127.0.0.1 <- Server: 0
Response: Success
Message: Parked calls will follow
Server: 0
127.0.0.1 <- Event: ParkedCallsComplete
127.0.0.1 <- Total: 0
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Follows
127.0.0.1 <- Privilege: Command
127.0.0.1 <- ActionID: fop2state
127.0.0.1 <- 0 results found.
127.0.0.1 <- --END COMMAND--
127.0.0.1 <- Server: 0
127.0.0.1 <- Response: Follows
127.0.0.1 <- Privilege: Command
127.0.0.1 <- ActionID: fop2notes
127.0.0.1 <- 0 results found.
127.0.0.1 <- --END COMMAND--
127.0.0.1 <- Server: 0
Do you know any hint?